E-Z HEAT AIRCRAFT ENGINE PREHEATER
49 155
₽
Описание
Note: Please see "Engine Application Guide" Click Here for the correct EZ Heat model number for your application.
Preheating engines for winter operations is at best a miserable chore and at worst can be a disaster for the plane, the pilot & flight operations - until the development of the E-Z Heat Aircraft Engine Heater. The E-Z Heat was designed to provide very efficient engine heating for virtually all propeller driven aircraft. The heaters consist of a flexible synthetic pad that easily conforms to the contours of the oil pan. This pad will heat 12 qts of oil from -40° to +60°F in an hour while using approximately 300 watts of electricity. The heater is 1/32" thick. which enables the immediate heat transfer from heater to engine.
The heaters are thermostatically controlled, so leaving them plugged in overnight means the plane will be ready to go in the morning. Normally, complete pre-heating takes only 3-5 hours for the entire engine to be nice and warm. With this new lighted plug (110V models only, 220V models include no plug to allow for European outlet variance), the owner simply needs to look out the window or peek in the hangar to see if they remembered to plug in their E-Z Heat engine pre-heater. Molded into the male plug end is a newly designed light emitting diode (LED). This LED allows the operator to visually recognize if there is electrical power to the preheat system even from a distance. FAA approved for certificated aircraft.
End your cold weather starting problems and reduce premature engine wear.
E-Z Heat Installation Instructions
Preheating engines for winter operations is at best a miserable chore and at worst can be a disaster for the plane, the pilot & flight operations - until the development of the E-Z Heat Aircraft Engine Heater. The E-Z Heat was designed to provide very efficient engine heating for virtually all propeller driven aircraft. The heaters consist of a flexible synthetic pad that easily conforms to the contours of the oil pan. This pad will heat 12 qts of oil from -40° to +60°F in an hour while using approximately 300 watts of electricity. The heater is 1/32" thick. which enables the immediate heat transfer from heater to engine.
The heaters are thermostatically controlled, so leaving them plugged in overnight means the plane will be ready to go in the morning. Normally, complete pre-heating takes only 3-5 hours for the entire engine to be nice and warm. With this new lighted plug (110V models only, 220V models include no plug to allow for European outlet variance), the owner simply needs to look out the window or peek in the hangar to see if they remembered to plug in their E-Z Heat engine pre-heater. Molded into the male plug end is a newly designed light emitting diode (LED). This LED allows the operator to visually recognize if there is electrical power to the preheat system even from a distance. FAA approved for certificated aircraft.
End your cold weather starting problems and reduce premature engine wear.
E-Z Heat Installation Instructions
Features
Power Consumption:
300 watts or less / Thermostatically Controlled
Power Requirement:
110/120 volts (models 440, 441 and 540 are available in 220 volts).
Installation:
The adhesive is already on the pad. All you need to do is peel and stick it on! (excluding model 470)
Preheat Time:
3 to 5 hours on cold soaked engine, although, since unit is thermostatically controlled, it may be left on overnight, or all the time. Cowl covers and prop covers are recommended for extreme cold weather, they also reduce preheat time.
Lite Brite Plug:
With this new lighted plug, the owner simply has to look out the window or peek in the hangar to see if they remembered to plug in their E-Z Heat engine pre-heater! (excluding model 470)
Weight:
Only 9 ounces!
Heat Transfer:
Convection/conduction, the safest way of heat transfer available. No flames or glowing elements are potential fire hazards.
E-Z Heat Models:
300 watts or less / Thermostatically Controlled
Power Requirement:
110/120 volts (models 440, 441 and 540 are available in 220 volts).
Installation:
The adhesive is already on the pad. All you need to do is peel and stick it on! (excluding model 470)
Preheat Time:
3 to 5 hours on cold soaked engine, although, since unit is thermostatically controlled, it may be left on overnight, or all the time. Cowl covers and prop covers are recommended for extreme cold weather, they also reduce preheat time.
Lite Brite Plug:
With this new lighted plug, the owner simply has to look out the window or peek in the hangar to see if they remembered to plug in their E-Z Heat engine pre-heater! (excluding model 470)
Weight:
Only 9 ounces!
Heat Transfer:
Convection/conduction, the safest way of heat transfer available. No flames or glowing elements are potential fire hazards.
E-Z Heat Models:
- Model 270 - 3" x 5 3/4" x 1/32"
- Model 440 - 4" x 4" x 1/32"
- Model 441 - 4" x 5 1/2" x 1/32"
- Model 442 - 2" 1/8" x 13" x 1/32"
- Model 470 - 4" x 7" x 1/32"
(no lite brite or peel & stick adhesive) - Model 5402 pads - 3" x 5 3/4" 1/32" and 3" x 4" x 1/32"
| Арт. | MPN | Описание | Цена | Add to cart form |
|---|---|---|---|---|
| 07-00756
|
360
|
E-Z HEAT ENGINE HEATER 360
|
$
163.85
|
|
| 07-05210
|
442
|
E-Z HEAT ENGINE HEATER 442
|
$
163.85
|
|
| 07-05315
|
270
|
E-Z HEAT AIRCRAFT ENGINE PREHEATER
|
$
163.85
|
|
| 07-05200-2
|
441 220 VOLT
|
E-Z HEAT ENGINE HEATER 441 220V
|
$
163.85
|
|
| 07-05200
|
441
|
E-Z HEAT ENGINE HEATER 441
|
$
163.85
|
|
| 07-05345
|
540
|
E-Z HEAT ENGINE HEATER 540
|
$
187.75
|
|
| 07-05100
|
440
|
E-Z HEAT ENGINE HEATER 440 110V
|
$
163.85
|
|
| 07-01320
|
470
|
E-Z HEAT ENGINE HEATER 470
|
$
163.85
|
Отзывы Оставить отзыв
Вопросы и ответы
Отзывы ещё не добавлены