ALCOHOL RESISTANT GAS TANK SEALER

10 770 ₽

Описание

This is impervious to all fuel types. Over 2,000,000 sold to date. It is the best way to repair and restore your fuel tank. Simple application, includes extensive application information and product information sheet. Will seal pinhole leaks and prevent rusting. 1 Pint will seal a 10-12 gallon tank. Good for all fuel types. Works well with all metal and fiberglass tanks.

Note: For Experimental Aircraft Only!

Арт.	Описание	Цена	Add to cart form
09-03477	ALCOHOL RESISTANT GAS TANK SEALER	$ 35.90
09-02566	ALCOHOL RESISTANT GAS TANK SEALER GALLON	$ 88.75

Отзывы Оставить отзыв

Отзывы ещё не добавлены

Вопросы и ответы

I'm looking at sealing a very slight seepage at the sump drain flange on my RV-4- Aluminum tank with aluminum sump valve flange- and I use motor gas w/ethanol in my plane. I am looking at something with low viscosity to flow into the area that is leaking, and perhaps setting up a slight vacuum with a toilet punger to draw the sealant into the seepage.(this is aerospace engineering, after all). Does this product have a fairly low viscosity, or can it be thinned a bit with, say, MEK?

Per the vendor, if it is used shortly after purchase, part number 09-03477 should not need anything to thin out the product. Make sure it is well mixed and it should be fine without any additional products.

Will this also adhere to plastic gas tank such as on a snowmachine? It would also have to be resistant to extreme temperatures such as -40 to +180 approx.

This sealer is only recommended for metal or fiberglass fuel tanks.

You say this works in fiberglass tanks, would it work in fiberglass foam epoxy tanks like the Long EZ has?

This is a tricky question. Yes it should work, but there are no specific tests done with any specific epoxy or resin system used to make a fiberglass tank. As long as the tank is cleaned and prepped properly, it should work just fine.

You say this works in fiberglass tanks, would it work in fiberglass foam epoxy tanks like the Long EZ has?

Can this be poured into wing tanks and sloshed around to seal leaks?

Per out product support manager: it is a sloshing material that will fill small pin hole leaks and seal the inner tank. It can be poured in and sloshed around in a fuel tank.

What is the shelf life before this alcohol resistant gas tank sealer must be used?

Per the supplier: this product has a 2 year shelf life that starts once it is opened.

What is needed to prepare the inner tank surface before using the Alcohol resistant gas tank sealer?

Per the manufacturer: The entire interior of the tank must be dry. If only one small area of the tank is not dry or has foreign matter that may keep the sealer from adhering, the sealer will not stick to those areas and could come loose and float around in your tank and eventually come through the fuel pick up tube and clog the fuel pump and carburetor. The solvent for this sealer is methyl ethyl ketone (mek). Before introducing any additives to fuel tank after sealer has been installed, be sure that the product you introduce does not contain (mek).

Is the alcohol resistant tank sealer (pn 09-03477) comparable with the pro-seal ps 890 class b (pn 09-38560)?

The 09-03477 is a sloshing sealer that gets poured in a fuel tank and the tank rotated so the material gets on all parts of the tank. The 09-38560 is a much thicker material and requires a brush to spread the material.

Can this product be used in aluminum floats or aluminum boats to seal rivets and be applied with a brush?

The primary purpose of this material is to coat the inside walls of a fuel tank for protection. It is a pour in and slosh around material. I could not find any information as to how well it would work if brushed on, or what size pin holes, or rivets, it would seal.

What is the application thickness that the manufacture recommends? Is this a single stage component? Or mix A with B?

This is a single stage component. There is no thickness that we recommend. Each application can vary. The product generally leaves behind a very thin coating. It is not supposed to be very thick. The idea is to pour the product in to the tank and slosh it around. Once all of the walls of the tank have been hit, they customer should drain the remaining sealer out back in to the can. There should be no puddling of the product as this will prevent it from drying properly. If the customer wants to do a 2nd coat after 24 hours with the remaining product, that is fine.

Is this Alcohol Resistant Gas Tank sealant considered dangerous goods?

Yes, this is considered hazardous material. For ground shipping within the USA there is no hazmat fee, but for any shipments, it will incur significant hazardous charges.

What is the working time of the product?

It has a pretty long working time. It's designed to be sloshed in the tank and then the excess is poured back in the can. It doesn't cure for 24-72 hours after that.

Does this product work with diesel?

Yes this sealer can stand up to diesel fuel, the issue will be in the prep work before applying the sealer. The tank must be 100% cleaned. No residue can be left or the sealer may not stick as the diesel has an oil mix in it that can be difficult to remove when the tank is empty. Boiling out the tank, or a thorough cleaning with a strong cleaner de-greaser , like ours, will do the job.

What are the temperature limits? Can it be used on a and heated to about 200 degrees f?

Per the vendor, this would not work for this application. It does not have heat rating.